mhdopa.blogg.se - Ic-7800 setup with microham mkii

#Ic 7800 setup with microham mkii install
#Ic 7800 setup with microham mkii mod
#Ic 7800 setup with microham mkii software
#Ic 7800 setup with microham mkii download
#Ic 7800 setup with microham mkii windows

For example, WSJT-X has a vertical slider on the lower right labelled “Pwr”.

#Ic 7800 setup with microham mkii software

Your digital mode software should have an option or on-screen setting to change this level. Ultimately, this is the best way to control your RF output power.

The output volume of your computer audio out (microphone).

The effective output power is determined by a combination of three settings: Reduce Your Transmit Powerĭon’t forget to reduce your RF output power when on digital modes. Values for AGC, NOTCH, NB, NR for digital modes.

NB (noise blanker) and NR (noise reduction) both OFF.

No Notch Filter – press the NOTCH button until it is OFF.

You can check on the FUNCTION screen – COMP should be disabled.

No compression – this should be automatically disabled when you are in USB-D mode.

Alternatively, if you use RTTY or other narrower modes, you can use FIL2 or FI元 instead for BPSK31. So change the USB-D Filter 1 by long-pressing the FIL1 button on the screen, and set the BW to 3.0K or wider. The default for the Data modes is very narrow, and this doesn’t work well for BPSK31. You can set the Filters (1-3) for each mode (USB, USB-D, AM, etc.). It also lets you define a custom filter for BPSK31.

#Ic 7800 setup with microham mkii mod

(Click the Mode label in the upper left, select USB and select DATA.) The USB-D mode is needed so that the DATA MOD option works as expected. Now, when using a digital mode, you should use the USB-D mode. You want the fastest Baud rate possible.ĪF Output Level 40% (see text) USB MOD level, DATA OFF MOD DATA MOD USB Use USB-D Mode A side effect of this is the the CI-V USB Baud Rate will be limited to 19200. This setting seems to be required for most software programs using the CI-V function. Note: the CI-V USB Port setting should be set to “Link to ”. These are usually described in some detail for each digital control program you use, and can be set up so that all your software will talk to your IC-7300.

#Ic 7800 setup with microham mkii install

They are related to the ICOM USB port driver you must install for Windows, the serial COM port number that ends up being the one used for your particular PC, and the baud rate you decide to use.

CI-V – These settings relate to the USB control interface and are controlled by the setup of your digital software.

Use the USB connector to get your audio from your computer when in data mode (USB-D). This new option was technically unnecessary, but many people were confused by the DATA OFF and DATA (ON) options, and were getting no audio when switching between Digital and Microphone modes.

Note that the versions of the 7300 firmware after late 2017 have added an option for this setting called MIC, ACC. This would normally be your microphone (MIC) when in regular USB/LSB modes. This option tells your IC-7300 which audio input source (modulation) to use when the DATA mode is OFF. The value is also related to your output power. This value can vary depending on your software. This should assure you have a clean output signal. Set this so that you get a minimal ALC meter reading when transmitting. Depending on your software, you may want to change this. This affects the Audio Level heard by your computer. Set UP your IC-7300 for Digital Modes Connectors Settings In this article, use the context to differentiate USB (PC Universal Serial Bus) vs.

#Ic 7800 setup with microham mkii windows

Windows will try to auto-install its own driver if you simply plugin the USB cable from the 7300 to the computer, and that one doesn’t work with the Icom USB interface.

#Ic 7800 setup with microham mkii download

Be sure that you first download and install the Icom USB driver beforeconnecting your 7300 to the Windows computer the very first time.

It is easiest to connect the IC-7300 using a single USB cable. See my other posts that address the specifics of DXLab Commander and HRD. These settings might be different for DXLab Commander and Ham Radio Deluxe. (e.g., BPSK31 using Ham Radio Deluxe Digital Master 780, fldigi, WSJT-X) These settings seem to work equally well with most digital modes, and digital mode software. This post shows the settings I use with my IC-7300 for digital modes over the USB connection from the 7300 to a Windows computer.